PCB科技 - PCB高頻選板生產加工

的定義 高頻板 用於電路板生產 <一 href="/tw/high-frequency-pcb.html" target="_self" textvalue="印刷電路板 高頻板">印刷電路板高頻板 指電磁頻率較高的特殊電路板, which is used in the fields of high frequency (frequency greater than 300MHZ or wavelength less than 1 meter) and microwave (frequency greater than 3GHZ or wavelength less than 0.1 meter) The 印刷電路板 是使用普通剛性電路板製造方法的一部分工藝或使用特殊加工方法在微波基板覆銅板上製造的電路板. 一般來說, a 高頻板 可以定義為頻率高於1GHz的電路板!

隨著科學技術的飛速發展, more and more equipment designs are applied in the microwave frequency band (>1GHZ) or even in the millimeter wave field (30GHZ). 這也意味著頻率越來越高, 和 印刷電路板電路板 The requirements for substrates are also getting higher and higher. 例如, 基板資料需要具有良好的電力效能, 良好的化學穩定性, 隨著功率訊號頻率的新增，襯底上的損耗非常小, 因此 高頻板 突出顯示. 2. 印刷電路板 高頻板 應用領域：移動通信產品； 功率放大器, 低雜訊放大器, 等.； 功率分配器等無源元件, 耦合器, 雙工器, 篩檢程式, 等.； 汽車防撞系統, 衛星系統, 無線電系統, 和其他領域, 高頻電子設備是發展趨勢.
2. 印刷電路板高頻板 應用領域：移動通信產品； 功率放大器, 低雜訊放大器, 等.； 功率分配器等無源元件, 耦合器, 雙工器, 篩檢程式, 等.； 汽車防撞系統, 衛星系統, 無線電系統, 和其他領域, 高頻電子設備是發展趨勢.
Classification of high frequency board powder ceramic filled thermosetting 材料

A. Manufacturer:
4350B/4003C from Rogers
Arlon's 25N/25FR
Taconic's TLG series
B. 印刷電路板 circuit board processing method:
The processing process is similar to epoxy resin/glass woven cloth (FR4), 除了板材相對易碎且容易斷裂外. 鑽孔和敲鑼時, 鑽頭和弓刀的壽命降低20%. PTFE (polytetrafluoroethylene) 材料
A. 製造商：RO3000系列, RT系列, TMM series from Rogers
Arlon's AD/AR系列, IsoClad系列, CuClad series
Taconic's RF series, TLX系列, TLY series
Taixing Microwave's F4B, F4BM, F4BK, TP-2
B. 處理方法：1. Cutting: The protective film must be kept for cutting to prevent scratches and creasing
2. Drilling
1. Use a brand new drill tip (standard 130), 一個接一個是最好的, the pressure of the presser foot is 40psi
2. 鋁板是蓋板, and then the PTFE plate is tightened with a 1mm melamine backing plate
3. 鑽孔後, use an air gun to blow out the dust in the hole
4. Use the most stable drilling rig and drilling parameters (basically the smaller the hole, 鑽孔速度越快, 晶片負載越小, the smaller the return speed)
3. Hole treatment
Plasma treatment or sodium naphthalene activation treatment is conducive to hole metallization
4.PTH copper sink
1 After the micro-蝕刻 (the micro-etching rate has been controlled by 20 microinches), the PTH pulls from the de-oiler cylinder to enter the board
2 If necessary, 通過第二個PTH, just start the board from the expected cylinder
5. Solder mask
1 Pre-treatment: Use acidic plate washing instead of mechanical grinding plate
2 Baking plate after pretreatment (90 degree Celsius, 30min), brush with green oil to cure
3 Baking plates in three stages: one section of 80 degree Celsius, 100攝氏度, 150攝氏度, each for 30 minutes (if you find that the substrate surface is oily, you can rework: wash off the green oil and reactivate it)
6.Gong board
Lay the white paper on the circuit surface of the PTFE board, 並用FR-4基板或厚度為1的酚醛基板上下夾住.0毫米蝕刻以去除銅, 如圖所示： 高頻板 lamination method
The burrs on the back of the gong board need to be carefully trimmed by hand to prevent damage to the substrate and copper surface, 然後用相當大尺寸的無硫紙分離, 並目視檢查. 减少毛刺, 關鍵的一點是，龔板過程必須有一個良好的效果.
Process flow NPTH's PTFE sheet processing flow
Cutting-Drilling-Dry Film-Inspection-Etching-Erosion Inspection-Solder Mask-Characters-Spray Tin-Forming-Testing-Final Inspection-Packaging-Shipment
PTH's PTFE plate processing flow
Cutting-drilling-hole treatment (plasma treatment or sodium naphthalene activation treatment)-copper immersion-board electricity-dry film-inspection-diagram electricity-etching-corrosion inspection-solder mask-character-spray tin-molding-test-final Inspection-Packaging-Shipping
Summarize the difficulties of 印刷電路板高頻板 processing
1. Immersion copper: the hole wall is not easy to be copper
2. 地圖傳輸的線隙和沙眼控制, etching, line width
3. 綠油工藝：綠油附著力, green oil foaming control
4. 嚴格控制每道工序板面劃痕.