PCB News - Power supply PCB design points and electrical requirements

In any switching power supply design, the physical design of the PCB board is the last link. If the design method is improper, the PCB may radiate too much electromagnetic interference and cause the power supply to work unstable. The following are the matters needing attention in each step analyze:

1. The design process from schematic to PCB

establish component parameters -> input principle netlist -> design parameter settings -> manual layout -> manual wiring -> verify design -> review -> CAM output.

Two, parameter setting

The distance between adjacent wires must be able to meet electrical safety requirements, and in order to facilitate operation and production, the distance should be as wide as possible. The minimum spacing must be at least suitable for the voltage tolerated. When the wiring density is low, the spacing of the signal lines can be increased appropriately. For signal lines with a large gap between high and low levels, the spacing should be as short as possible and the spacing should be increased. Generally, Set the trace spacing to 8mil. The distance between the edge of the inner hole of the pad and the edge of the printed board should be greater than 1mm, which can avoid the defects of the pad during processing. When the traces connected to the pads are thin, the connection between the pads and the traces should be designed into a drop shape. The advantage of this is that the pads are not easy to peel, but the traces and the pads are not easily disconnected.

Three, component layout

Practice has proved that even if the circuit schematic is designed correctly and the printed circuit board is not designed properly, it will have an adverse effect on the reliability of electronic equipment. For example, if the two thin parallel lines of the printed board are close together, the signal waveform will be delayed and reflected noise will be formed at the terminal of the transmission line. The performance drops, so when designing the printed circuit board, you should pay attention to adopting the correct method. Each switching power supply has four current loops:

(1). Power switch AC circuit

(2). Output rectifier AC circuit

(3). Input signal source current loop

(4). Output load current loop The input loop charges the input capacitor through an approximate DC current. The filter capacitor mainly acts as a broadband energy storage; similarly, the output filter capacitor is also used to store high-frequency energy from the output rectifier. At the same time, the DC energy of the output load loop is eliminated. Therefore, the terminals of the input and output filter capacitors are very important. The input and output current loops should only be connected to the power supply from the terminals of the filter capacitor respectively; if the connection between the input/output loop and the power switch/rectifier loop cannot be connected to the capacitor The terminal is directly connected, and the AC energy will be radiated into the environment by the input or output filter capacitor. The AC circuit of the power switch and the AC circuit of the rectifier contain high-amplitude trapezoidal currents. The harmonic components of these currents are very high. The frequency is much greater than the fundamental frequency of the switch. The peak amplitude can be as high as 5 times the amplitude of the continuous input/output DC current. The transition time is usually About 50ns. These two loops are the most prone to electromagnetic interference, so these AC loops must be laid out before the other printed lines in the power supply. The three main components of each loop are filter capacitors, power switches or rectifiers, inductors or transformers. Place them next to each other and adjust the position of the components to make the current path between them as short as possible. The best way to establish a switching power supply layout is similar to its electrical design. The best design process is as follows:

1. Place the transformer

2. Design the power switch current loop

3. Design the output rectifier current loop

4. Control circuit connected to AC power circuit

Design the input current source loop and input filter When designing the output load loop and output filter according to the functional unit of the circuit, all the components of the circuit should be laid out in accordance with the following principles:

(1) First, consider the PCB size. When the PCB size is too large, the printed lines will be long, the impedance will increase, the anti-noise ability will decrease, and the cost will increase; if the PCB size is too small, the heat dissipation will not be good, and adjacent lines will be easily disturbed. The best shape of the circuit board is rectangular, and the aspect ratio is 3:2 or 4:3. The components located on the edge of the circuit board are generally not less than 2mm away from the edge of the circuit board.

(2) When placing the device, consider the subsequent soldering, not too dense.

(3) Take the core component of each functional circuit as the center and arrange the layout around it. The components should be evenly, neatly and compactly arranged on the PCB, minimize and shorten the leads and connections between the components, and the decoupling capacitor should be as close as possible to the VCC of the device.

(4) For circuits operating at high frequencies, the distributed parameters between components should be considered. Generally, the circuit should be arranged in parallel as much as possible. In this way, it is not only beautiful, but also easy to install and weld, and easy to mass produce.

(5) Arrange the position of each functional circuit unit according to the circuit flow, so that the layout is convenient for signal circulation, and the signal is kept in the same direction as possible.

(6) The first principle of the layout is to ensure the layout rate of the wiring, pay attention to the connection of the flying leads when moving the device, and put the connected devices together.

(7) Reduce the loop area as much as possible to suppress the radiation interference of the switching power supply.

The above is an introduction to the main points of power supply PCB design and electrical requirements. Ipcb also provides PCB manufacturers and PCB manufacturing technology.