PCB Technical - De-drilling and etchback technology for FPC boards

1 Overview

De-drilling and etchback is an important process before the electroless copper plating or direct copper electroplating after the CNC drilling of the rigid-flex printed circuit board. If the rigid-flex printed circuit board is to achieve reliable electrical interconnection, it must be combined Rigid-flex printed circuit boards are composed of special materials. According to the characteristics of polyimide and acrylic as the main materials, which are not resistant to strong alkalis, appropriate de-drilling and etchback technologies are selected. Rigid-flex printed circuit board de-drilling and etchback technologies are divided into wet technology and dry technology. The following two technologies will be discussed together with colleagues.

2. Rigid-flex printed circuit board wet de-drilling and etchback technology

Rigid-flex printed circuit board wet de-drilling and etchback technology consists of the following three steps:

L Bulking (also called swelling treatment). Use alcohol ether leavening liquid to soften the pore wall substrate, destroy the polymer structure, and increase the surface area that can be oxidized, so that the oxidation effect is easy to proceed. Generally, butyl carbitol is used to swell the pore wall substrate.

L Oxidation. The purpose is to clean the hole wall and adjust the hole wall charge. At present, three methods are traditionally used in China.

1.. Concentrated sulfuric acid method: Because concentrated sulfuric acid has strong oxidizing property and water absorption, it can carbonize most of the resin and form water-soluble alkyl sulfonates to be removed. The reaction formula is as follows: CmH2nOn+H2SO4--mC+nH2O The effect of resin drilling on the hole wall is related to the concentration of concentrated sulfuric acid, the processing time and the temperature of the solution. The concentration of concentrated sulfuric acid used to remove drilling dirt should not be less than 86%, 20-40 seconds at room temperature. If etchback is required, the temperature of the solution should be appropriately increased and the treatment time should be prolonged. Concentrated sulfuric acid only works on the resin and is not effective on the glass fiber. After the hole wall is etched by the concentrated sulfuric acid, the glass fiber head will protrude from the hole wall, which needs to be treated with fluoride (such as ammonium bifluoride or hydrofluoric acid). When using fluoride to treat the protruding glass fiber head, the process conditions should also be controlled to prevent the wicking effect caused by the over-corrosion of the glass fiber. The general process is as follows:

H2SO4: 10%

NH4HF2: 5-10g/l

Temperature: 30 degree Celsius Time: 3-5 minutes

According to this method, the punched rigid-flex printed circuit board was drilled and etched, and then the hole was metalized. Through metallographic analysis, it was found that the inner layer was not thoroughly drilled at all, resulting in the copper layer and the hole wall. The adhesion is low. For this reason, when the metallographic analysis is used for thermal stress experiment (288°C, 10±1 seconds), the copper layer on the hole wall falls off and the inner layer is broken.

Besides, ammonium bifluoride or hydrofluoric acid is very toxic, and wastewater treatment is very difficult. The more important thing is that polyimide is inert in concentrated sulfuric acid, so this method is not suitable for de-drilling and etchback of rigid-flex printed circuit boards.

2. Chromic acid method: Because chromic acid has strong oxidizing properties and strong etching ability, it can break the long chain of the pore wall polymer material, and cause oxidation and sulfonation, and generate more affinity on the surface. Water-based groups, such as carbonyl (-C=O), hydroxyl (-OH), sulfonic acid group (-SO3H), etc., to improve its hydrophilicity, adjust the charge of the hole wall, and achieve the removal of hole wall drilling dirt and concave The purpose of the eclipse. The general process formula is as follows:

Chromic anhydride CrO3: 400 g/l

Sulfuric acid H2SO4: 350 g/l

Temperature: 50-60 degree Celsius Time: 10-15min

According to this method, the punched rigid-flex printed circuit board was de-drilled and etched, and then the holes were metallized. Metallographic analysis and thermal stress experiments were carried out on the metallized holes, and the results were in full compliance with the GJB962A-32 standard. .

Therefore, the chromic acid method is also suitable for the de-drilling and etchback of rigid-flex printed circuit boards. For small businesses, this method is indeed very suitable, simple and easy to operate, and more importantly, the cost, but this method is the only one Unfortunately, there is a toxic substance chromic anhydride.

3. Alkaline potassium permanganate method: At present, due to lack of professional technology, many PCB manufacturers still follow rigid multi-layer printed circuit board de-drilling and etchback technology-alkaline potassium permanganate technology to deal with rigid- For flexible printed circuit boards, after removing the resin drilling dirt by this method, the resin surface can be etched to produce small uneven pits on the surface, so as to improve the bonding force of the hole wall plating layer and the substrate. In a high temperature and high alkali environment, Potassium permanganate is used to oxidize and remove swollen resin contamination. This system is very effective for general rigid multi-layer boards, but it is not suitable for rigid-flex printed circuit boards because the main insulating base of rigid-flex printed circuit boards The material polyimide is not alkali-resistant, and will swell or even partially dissolve in the alkaline solution, not to mention the high temperature and high alkali environment. If this method is adopted, even if the rigid-flex printed circuit board is not scrapped at that time, it will greatly reduce the reliability of the equipment using the rigid-flex printed circuit board in the future.

L Neutralization. The substrate after oxidation treatment must be cleaned to prevent contamination of the activation solution in the subsequent process. For this reason, it must go through a neutralization and reduction process. Different neutralization and reduction solutions are selected according to different oxidation methods.

3. Dry de-drilling and etchback technology for rigid-flex printed circuit boards

At present, the popular dry method at home and abroad is plasma decontamination and etchback technology. Plasma is used in the production of rigid-flex printed circuit boards, mainly to de-drill the hole wall and modify the surface of the hole wall. The reaction can be seen as a gas and solid phase chemical reaction between the highly activated plasma, the polymer material of the pore wall and the glass fiber, and the generated gas product and some unreacted particles are pumped away by the vacuum pump. Dynamic chemical reaction balance process. According to the polymer materials used in rigid-flex printed circuit boards, N2, O2, and CF4 gases are usually selected as the original gas. Among them, N2 plays the role of cleaning vacuum and preheating.

The schematic formula of the plasma chemical reaction of O2+CF4 mixed gas is:

O2+CF4 O+OF+CO+COF+F+e-+…….

Plasma

Due to the acceleration of the electric field, it becomes a highly reactive particle and collides with O and F particles to generate highly reactive oxygen radicals and fluorine radicals, which react with polymer materials as follows:

[C, H, O, N]+[O+OF+CF3+CO+F+…] CO2+HF+H2O+NO2+……

The reaction of plasma and glass fiber is:

SiO2+［O+OF+CF3+CO+F+…］ SiF4+CO2+CaL

So far, the plasma treatment of rigid-flex printed circuit boards has been realized.

It is worth noting that the carbonylation reaction of O in atomic state with C-H and C=C causes the addition of polar groups on the polymer bond, which improves the hydrophilicity of the surface of the polymer material.

good.

Rigid-flex printed circuit boards treated with O2+CF4 plasma and then treated with O2 plasma can not only improve the wettability (hydrophilicity) of the hole wall, but also remove the reaction. After the end of the sediment and the halfway product of the reaction incomplete. After processing rigid-flex printed circuit boards with plasma technology to remove dirt and etchback, and after direct electroplating, metallographic analysis and thermal stress experiments were carried out on the metallized holes, and the results were in full compliance with the GJB962A-32 standard.

4 Conclusion

In summary, whether it is dry or wet to produce PCBs, if you choose a suitable method for the characteristics of the main material of the system, you can achieve the purpose of de-drilling and concave etching of the rigid-flex interconnection motherboard.