PCB News - Vias for high-speed PCB circuit board design

Vias for high-speed PCB circuit board design

At present, the design of high-speed PCB circuit boards is widely used in the fields of communication, computer, graphics and image processing. All high-tech value-added electronic product designs are pursuing low power consumption, low electromagnetic radiation, high reliability, miniaturization, light weight, etc. Features. In order to achieve the above goals, via design is an important factor in high-speed PCB design. It consists of the hole, the pad area around the hole and the isolation area of the POWER layer, which are usually divided into three types: blind hole, buried hole and through hole. In the PCB circuit board design process, through the analysis of the parasitic capacitance and parasitic inductance of the via, some precautions in the design of the high-speed PCB via are summarized.

1. Via

Vias are an important factor in the design of multi-layer PCB circuit boards. A via is mainly composed of three parts, one is the hole; the other is the pad area around the hole; and the third is the isolation area of the POWER layer. The process of the via hole is to plate a layer of metal on the cylindrical surface of the hole wall of the via hole by chemical deposition to connect the copper foil that needs to be connected to the middle layers, and the upper and lower sides of the via hole are made into ordinary pads The shape can be directly connected with the lines on the upper and lower sides, or not connected. Vias can play the role of electrical connection, fixing or positioning devices.

Vias are generally divided into three categories: blind holes, buried holes and through holes.

Blind hole: It is located on the top and bottom surfaces of the printed circuit board with a certain depth and is used for the connection of the surface circuit and the inner circuit below. The depth of the hole and the diameter of the hole usually do not exceed a certain ratio.

Buried hole: refers to the connection hole located in the inner layer of the printed circuit board, which does not extend to the surface of the circuit board.

Both blind and buried holes are located in the inner layer of the circuit board, and are completed by a through-hole forming process before lamination, and several inner layers may be overlapped during the formation of the via.

Through hole: This kind of hole passes through the entire circuit board and can be used for internal interconnection or as a component installation positioning hole. Since through holes are easier to implement in process and lower cost, generally printed circuit boards use through holes. .

2. Parasitic capacitance of vias

The via itself has parasitic capacitance to ground. If the diameter of the isolation hole on the ground layer of the via is D2, the diameter of the via pad is D1, the thickness of the PCB is T, and the dielectric constant of the board substrate is ε, then The parasitic capacitance of the via is similar to:

C=1.41εTD1/(D2-D1)

The main effect of the parasitic capacitance of the via hole on the circuit is to prolong the rise time of the signal and reduce the speed of the circuit. The smaller the capacitance value, the smaller the effect.

3. Parasitic inductance of vias

The via itself has parasitic inductance. In the design of high-speed digital circuits, the harm caused by the parasitic inductance of the via is often greater than the influence of the parasitic capacitance. The parasitic series inductance of the via will weaken the function of the bypass capacitor and weaken the filtering effect of the entire power system. If L refers to the inductance of the via, h is the length of the via, and d is the diameter of the center hole, the parasitic inductance of the via is approximately: L=5.08h[ln(4h/d)+1]

It can be seen from the formula that the diameter of the via has a small influence on the inductance, and the length of the via has the greatest influence on the inductance.

4. Non-through via technology

Non-through vias include blind vias and buried vias.

In the non-through via technology, the application of blind vias and buried vias can greatly reduce the size and quality of PCBs, reduce the number of layers, improve electromagnetic compatibility, increase the characteristics of electronic products, reduce costs, and also make the design work more Simple and fast. In traditional PCB design and processing, through holes will bring many problems. First, they occupy a large amount of effective space, and secondly, a large number of through holes are densely packed and also cause huge obstacles to the inner wiring of the multilayer PCB. These through holes take up the space required for the wiring, and they intensively pass through the power supply and the ground. The surface of the wire layer will also destroy the impedance characteristic of the power ground wire layer and make the power ground wire layer ineffective. And the conventional mechanical method of drilling will be 20 times the workload of non-through hole technology.

In the PCB design, although the size of the pads and vias have been gradually reduced, if the thickness of the board layer is not proportionally reduced, the aspect ratio of the through hole will increase, and the increase of the aspect ratio of the through hole will reduce the reliability. With the maturity of advanced laser drilling technology and plasma dry etching technology, it is possible to apply non-penetrating small blind holes and small buried holes. If the diameter of these non-penetrating vias is 0.3mm, the parasitic parameters will be About 1/10 of the original conventional hole, which improves the reliability of PCB.

Due to the non-through via technology, there are few large vias on the PCB, which can provide more space for routing. The remaining space can be used for large-area shielding purposes to improve EMI/RFI performance. At the same time, more remaining space can also be used for the inner layer to partially shield the device and key network cables, so that it has the best electrical performance. The use of non-through vias makes it easier to fan out the device pins, making it easy to route high-density pin devices (such as BGA packaged devices), shortening the wiring length, and meeting the timing requirements of high-speed circuits.

5. Via selection in ordinary PCB

In the ordinary PCB design, the parasitic capacitance and parasitic inductance of the via have little effect on the PCB circuit board design. For the 1-4 layer PCB circuit board design, 0.36mm/0.61mm/1.02mm (drilled hole/pad /POWER isolation area) via holes are better, some special signal lines (such as power lines, ground lines, clock lines, etc.) can choose 0.41mm/0.81mm/1.32mm vias, or other sizes can be selected according to the actual situation Of vias.

6. Via design in high-speed PCB circuit board

Through the above analysis of the parasitic characteristics of the vias, we can see that in the design of high-speed PCBs, seemingly simple vias often bring great negative effects to the circuit design. In order to reduce the adverse effects caused by the parasitic effects of the vias, the following can be done in the design:

(1) Choose a reasonable via size. For the PCB design of the general density of PCB multilayer circuit boards, it is better to use 0.25mm/0.51mm/0.91mm (drilled holes/pads/POWER isolation area) vias; for some high-density PCBs, 0.20 can also be used. For vias with mm/0.46mm/0.86mm, you can also try non-through vias; for power or ground vias, you can consider using a larger size to reduce impedance;

(2) The larger the POWER isolation area, the better, considering the via density on the PCB, generally D1=D2+0.41;

(3) The signal wiring on the PCB circuit board should not be changed as much as possible, which means that the vias should be reduced as much as possible;

(4) The use of a thinner PCB is beneficial to reduce the two parasitic parameters of the via;

(5) The power and ground pins should be close to the vias. The shorter the lead between the vias and the pins, the better, because they will increase the inductance. At the same time, the power and ground leads should be as thick as possible to reduce impedance;

(6) Place some grounding vias near the vias of the signal layer to provide a short-distance loop for the signal.

Of course, specific issues need to be analyzed in detail when designing. Considering both cost and signal quality comprehensively, in high-speed PCB design, designers always hope that the smaller the via hole is, the better, so that more wiring space can be left on the board. In addition, the smaller the via hole, its own The smaller the parasitic capacitance, the more suitable for high-speed circuits. In the design of high-density PCB circuit boards, the use of non-through vias and the reduction in the size of vias has brought about an increase in cost, and the size of vias cannot be reduced indefinitely. It is affected by the drilling and drilling of circuit board manufacturers. The limitations of electroplating and other process technologies should be given balanced consideration in the design of high-speed PCB vias.