PCB Technical - PCB printed circuit board inspection details

Several key points for the later inspection of PCB circuit board design

When a PCB board is placed and routed, and no errors are reported for connectivity and spacing, is a PCB completed? The answer is of course no. Many beginners also include some experienced engineers. Due to time constraints or impatient or overconfidence, they often rashly and neglect the later inspections. As a result, some very basic bugs appeared, such as insufficient line width, component label silk screen pressed on vias, sockets too close, signal loops, and so on. As a result, electrical problems or process problems are caused, and the board must be re-printed in serious cases, resulting in waste. Therefore, after a PCB has completed the layout and routing, a very important step is the later inspection.

PCB inspection has many detailed elements. I have listed some of the most basic and error-prone elements that I consider to be the most error-prone elements for later inspection.

1. Component packaging

(1) Pad pitch. If it is a new device, draw the component package yourself to ensure that the spacing is appropriate. The pad spacing directly affects the soldering of the components.

(2) Via size (if any). For plug-in devices, the size of the vias should be left with sufficient margin, generally not less than 0.2mm is more appropriate.

(3) Contour silk screen. The outline silk screen of the device should be larger than the actual size to ensure that the device can be installed smoothly.

2. PCB layout

(1) IC should not be near the edge of the board

(2) The components of the same module circuit should be placed close to each other. For example, the decoupling capacitor should be close to the power supply pin of the IC, and the components that make up the same functional circuit should be placed in one area with a clear hierarchy to ensure the realization of the function.

(3) Arrange the position of the socket according to the actual installation. Sockets are all lead to other modules. According to the actual structure, in order to facilitate installation, the principle of proximity is generally adopted to arrange the position of the socket, and it is generally close to the edge of the board.

(4) Pay attention to the direction of the socket. The sockets are all directional, and if the direction is reversed, the wire must be re-customized. For flat sockets, the direction of the socket should be toward the outside of the board.

(5) There can be no devices in the Keep Out area.

(6) The source of interference should be far away from sensitive circuits. High-speed signals, high-speed clocks, or high-current switching signals are all interference sources and should be kept away from sensitive circuits, such as reset circuits and analog circuits. They can be separated by paving.

3. Wiring

(1) The size of the line width. The line width should be selected in combination with the process and the current carrying capacity, and the minimum line width cannot be less than the minimum line width of the PCB manufacturer. At the same time, the current carrying capacity is ensured, and the appropriate line width is generally selected at 1mm/A.

(2) Differential signal line. For differential cables such as USB and Ethernet, please note that the cables should be of equal length, parallel, and in the same plane, and the spacing is determined by the impedance.

(3) Pay attention to the return path of the high-speed line. High-speed lines are prone to electromagnetic radiation. If the wiring path and the return path are too large, it will form a single-turn coil to radiate electromagnetic interference outwards. Therefore, when wiring, pay attention to the return path next to it, and the multi-layer board is equipped with a power supply. Layers and ground planes can effectively solve this problem.

(4) Pay attention to the analog signal line. The analog signal line should be separated from the digital signal, and the wiring should be avoided to pass by interference sources (such as clocks, DC-DC power supply), and the wiring should be as short as possible.

4. EMC and signal integrity

(1) Termination resistance. High-speed lines or digital signal lines with higher frequencies and longer traces are best to have a matching resistor in series at the end.

(2) The input signal line is connected in parallel with a small capacitor. The signal line input from the interface should be connected to a small picofarad capacitor near the interface. The size of the capacitor is determined according to the strength and frequency of the signal, and cannot be too large, otherwise it will affect the signal integrity. For low-speed input signals, such as key input, a small capacitor of 330pF can be used.

(3) Driving ability. For example, a switching signal with a larger driving current can be driven by a transistor; for a bus with a larger fan-out number, a buffer (such as 74LS224) can be added to drive.

5. Silk screen

(1) Board name, time, PN code.

(2) Labeling. Mark the pins or key signals of some interfaces (such as arrays).

(3) Component label. The component labels should be placed in a suitable position, and dense component labels can be placed in groups. Be careful not to place it in the position of the via.

6. Other

Mark point. For PCB circuit boards that need machine soldering, two to three Mark points need to be added.