PCB Technical - What is the difference between wire, flying wire and network

Common problems in PCB design
(1) Part package refers to the appearance and solder joint position indicated when the actual part is soldered to the circuit board.
(2) The part packaging is only the appearance of the part and the location of the solder joints. The pure part packaging is only the concept of space, so different parts can share the same part packaging; on the other hand, the same kind of parts can also have different packaging, such as RES2 stands for resistance, and its packaging forms are AXAIL0.4, AXAIL0.3, AXAIL0.6, etc., so when using welding parts, you must know not only the name of the part but also the package of the part.

(3) The package of parts can be specified when designing the circuit diagram, or when introducing the netlist. When designing the circuit diagram, you can specify it in the Footprint setting item in the part properties dialog box, or you can specify the part package when importing the netlist.
What is the difference between wire, flying wire and network?
Wire is also called copper film trace, or wire for short. It is used to connect various solder joints and is the most important part of the printed circuit board. The design of the printed circuit board revolves around how to arrange the wires.
Another kind of wire related to the wire, often called flying wire or pre-pull wire. The flying line is generated by the system according to the rules after the network table is introduced, and is used to guide the wiring of a kind of connection.
Flying wire and wire are essentially different. The flying line is just a form of connection, it only shows the connection relationship between the various solder joints in form, and has no electrical connection significance. The wire is arranged according to the connection relationship between the solder joints indicated by the flying lead, and it is a connection line with electrical connection significance.

There is a difference between a network and a wire. The network also includes solder joints. Therefore, when referring to a network, it is not only a guide wire but also a solder joint connected to the wire.
What is the difference between the inner layer and the middle layer?
The middle layer and the inner layer are two concepts that are easy to confuse. The middle layer refers to the middle board layer used for wiring, and the wires are laid in this layer; the inner layer refers to the power layer or the ground layer. Generally, this layer is not wired, and it is composed of a whole piece of copper film.
What is an internal network table and an external network table, and what is the difference between the two?
The network table is divided into external network table and internal network table. The external network table refers to the imported network table, that is, the schematic network table generated by Sch or other schematic design software; the internal network table is the network table used for wiring inside the PCB system after modification based on the imported external network table. Strictly speaking, these two kinds of netlists are completely different concepts, but readers do not need to distinguish strictly.
(1) Wiring F In the circuit board wiring process, some networks need special treatment, such as some important data lines. In order to avoid interference from other components on the circuit board, these data lines and other components are often required to be enlarged during wiring. Safe distance between. These data lines can be classified into one category. This category can be added to the rules when setting the automatic wiring safety spacing rules, and the safety spacing should be increased appropriately. Then, when the automatic wiring is performed, the safety spacing of all data lines in this category is the same. Be enlarged; in the circuit board wiring process, the power and ground wires often need to be thickened to ensure the reliability of the connection. The power and ground wires can be classified into one category. When setting the automatic wiring wire width (Width Constraint) rule, You can add this class to the rule, and appropriately increase the wire width, then the power and ground wires in this class will become wider during automatic routing.
(2) Management circuit board assembly F For a large circuit board, there are many parts and packages on it, and there are thousands of networks, which is very messy, and the use of classes can easily manage the circuit board. For example, to classify all the input networks in the circuit board, when looking for a certain input network, you only need to search in this input network category; you can also classify all the finite voltage resistances in the circuit board, and you can search for a certain input network. When voltage-limiting resistors are used, you only need to find them in this category of voltage-limiting resistors.
How to add additional solder joints to the network?
You can add the solder joints to the circuit board first, then double-click the solder joints to open the solder joint properties setting dialog box, and select the appropriate network in the Net item in Advaced to complete the solder joint placement.
What is the use of inner segmentation?
The inner layer divided by can be used to connect some important circuits, which can improve the anti-interference ability and protect important circuits.
What is the effect of copper plating and what should be paid attention to?
The main function of copper coating is to improve the anti-interference ability of the circuit board. If the circuit is to be covered with wires or teardrops, then the copper coating should be done last.